Location:Home > T SERIES > Turbo Undefined 4 > How to Remove a VW Beetle 1.8 Turbo Head Gasket

How to Remove a VW Beetle 1.8 Turbo Head Gasket

Time:2014-06-04 02:10Turbochargers information Click:

Turbo Beetle head Gaske remove

remove the air guide between the air filter and lock carrier. Release the retaining clamps that attach the wiring harness to the left radiator frame. 2 Remove the No. 2 mounting bolts from the lock carrier with a socket wrench and support it with Support 3369. Remove the remaining mounting bolts from the lock carrier and pull the lock carrier out as far as it will go. Fasten 6 mm bolts to the lock carrier and fender to secure the lock carrier in place. 3 Disconnect the cable from the negative battery terminal to ensure the engine doesn't start while you are removing the cylinder head gasket. Detach the cooling fan drive belt from its pulleys and remove the cooling fan from the engine. 4 Drain the coolant from the radiator into a container and store for later use. Disconnect the intake manifold from the engine with a socket wrench. Detach the accessory drive belts from their pulleys. 5 Remove the regulator valves for the wastegate bypass and the evaporative emissions canister from the engine with a socket wrench. Detach the mass airflow sensor from the engine. 6 Disconnect the housing for the air cleaner with a socket wrench. Detach the wiring harnesses for the engine-coolant temperature sensor and any other electrical components needed to access the cylinder head. Detach the breather line from the crankcase. 7 Remove the fuel lines and oil line from the cylinder head. Disconnect the heat shield and turbocharger from the exhaust manifold with a socket wrench. Detach the coolant hose from the rear of the cylinder head. 8 Detach the upper cover for the timing belt with a socket wrench. Turn the crankshaft clockwise to align the timing mark on the crankshaft with the top dead center mark on the crankcase. Loosen the Torx bolt on the timing belt tensioner with a T45 Torx wrench and push the tensioner down to relieve the tension on the timing belt. 9 Remove the timing belt from the gear of the camshaft, including a... How to Change a Head Light Bulb on a 2002 VW Beatle Changing a head light bulb on a 2002 VW beetle requires removing the ... Changing a head light bulb on a 2002... How to Replace the Head Gasket on a 1988 VW Cabriolet How to Replace the Head Gasket on a 1992 Volkswagen. ... How to Remove a VW Beetle 1.8 Turbo Head Gasket. The... Volkswagen 1.8L 16V Engine Information The Volkswagen 1.8 liter turbo engine is a 150 ... The 2000 VW Beetle 1.8L turbo engine is an ... Specifications for... How to Inspect the Exhaust System on a VW Beetle The VW Beetle isnt the same car as the new beetle. ... This system included an evaporative control canister mounted between the... How to Replace Valve Cover Gasket in a VW Beetle How to Repair Leaking Valve Cover Gaskets. ... How to Remove a VW Beetle 1.8 Turbo Head Gasket. The New Beetle comes... List of Cars with Interference Motors List of Cars with Interference Motors. ... is the corolla 2004 fitted with an interference engine? Featured. 10 Tips for Used Car... How to Remove the Cylinder Head on a Volkswagen Passat How to Remove the Cylinder Head on a Volkswagen Passat. ... How to Remove a VW Beetle 1.8 Turbo Head Gasket. The... How to Remove a Turbo From a VW Diesel How to Remove a Turbo From a VW Diesel. ... How to Remove a VW Beetle 1.8 Turbo Head Gasket. The New... VW New Beetle Turbo Problems VW New Beetle Turbo ... VW offered the New Beetle with a turbocharged 1.8-liter four-cylinder engine. Volkswagen issued ... 2004 Volkswagen New... How to Replace the Head Gasket in a VW VR6 Install the intake manifold and exhaust manifolds to 18 foot-pounds with a torque wrench. ... How to Replace a VW Head Gasket;... How to Remove Locktight Bolts How to Loosen Up a Tight Lock. ... Rusted or extremely tight bolts can ... How to Remove a Broken Threaded Bolt... How to Replace Valve Cover Gasket in a VW Passat How to Replace Valve Cover Gasket in a VW ... the camshaft chain tensioner and place RTV sealant at the corners where... How to Remove Broken Bolts From an Engine Block Comments You May Also Like. How to Remove a Broken Threaded Bolt From an Engine Head. The head bolts on your engine... How to Replace the Oil Pan on a 2000 VW Beetle How to Replace the Oil Pan on a 2000 VW Beetle. ... (if the car has a 1.8 liter engine) by removing... How to Replace Head Studs on a VW Beetle How to Remove a Cylinder Head Stud. ... How to Bench Bleed a Master Cylinder in a VW Beetle. VW launched the... How to Replace the Oil Pan Gasket in a VW Beetle How to Replace the Oil Pan Gasket in a VW Beetle. If you notice that your VW Beetle is leaving a trail... How to Replace the Ignition Coil on a 1999 VW Beetle How to Replace the Ignition Coil on a 1999 VW Beetle. ... Remove the engine ... There are three bolts on the... , and remove the Torx bolt from the timing belt tensioner with the T45 Torx wrench. Rotate the bracket for the timing belt tensioner forward to access the valve cover and then remove the valve cover with a socket wrench. 10 Disconnect the mounting bolts for the cylinder head with a socket wrench. Lift the cylinder head from the engine block and remove the gasket from the engine block. Clean the remaining traces of gasket material from the cylinder head and engine block with a gasket scraper. Clean the bolt holes on the cylinder head with a shop cloth and blow them dry with compressed air. Related Searches References AutoZone: Volkswagen Cars 2000-05 Cylinder Head 2 More Like This How to Jump Start a 1973 VW Super Beetle '02 VW Jetta GLS Turbo Information How to Replace a VW Head Gasket How to Replace the Head Gasket in a VW VR6

Copyright infringement? Click Here!